This page provided to give you a close estimate of your costs.

**Prices are subject to change due to the fluctuating cost of parts, and final price is dependent on the which manufacturer’s parts are selected for use.**

Slide Options

 

Lower and flare ejection port                                                                        $60

Add relief cut to front of port to aid live round ejection                          $40

Serrate standard round top slide                                                                 $100

Flat top and serrate at 30 LPI                                                                       $170

Flat top and serrate at 30 LPI, single arrowhead pattern                       $185

Flat top and serrate at 30 LPI, double arrowhead pattern                     $195

Machine French borders                                                                                $95

Machine cocking serrations on front of slide                                             $90

Machine slide for dovetail front sights                                                        $40

Machine slide for dovetail rear sight (Novak or Heinie)                          $45

Fit new front sight blank to dovetail cut,                                                    $70

machine blank to spec for height, width,

& profile and serrate face 50 LPI, center, drill and pin to slide               

Fit plain black rear sight to dovetail cut                                                      $70

 

Fit new standard .45ACP KART 5” barrel,                                                 $275           

including link & pin, ream and polish chamber,

profile and polish feed ramp. Check and correct link down timing.

Recess cut barrel into bushing and re-crown at 45 degrees                    $60           

(protects the muzzle from damage)

Supply and fit EGW thick flange bushing                                                $100                   

(with Double D spring plug)

Supply and fit standard match grade bushing                                           $70

Supply, fit and tune Wilson “Bullet Proof” extractor                                $65

 

 

Frame Options

 

High cut grip and checker front strap at 25 LP                                       $270

High cut grip and checker front strap at 20 LPI                                     $260

   

High cut grip and serrate at 20 LPI                                                           $160

High cut trigger guard                                                                                   $75

(Included with above, lowers the gun in the hand for less felt recoil)

Countersink slide stop pin and flush cut slide stop pin                          $55

Enlarge/bevel magwell (with standard main spring housing)              $60

Enlarge/bevel magwell (with Legacy Custom style main spring          $150

housing for maximum rear ramp)

Machine main spring housing to match front strap treatment              $90

Machine feed ramp to correct specs                                                             $50

Round Butt main spring housing and frame                                              $65

Supply & fit Greider Precision trigger (any size)                                       $53

Supply, fit and blend beavertail grip safety                                                $149

Supply, fit and blend standard single side thumb safety                         $85

(Ed Brown)

Supply, fit and blend “Ambi” thumb safety (Ed Brown)                          $170

Supply and fit new extended ejector                                                            $55

Re-stake plunger tube                                                                                     $20

Supply & stake replacement bar stock plunger tube                                $40

 

 

 

Miscellaneous Options

 

Add tritium vials to sights                                                                            POR

Trigger Job – Series 70 – 3.5# to 5# crisp                                               $85

(Price does not include any necessary parts)

Trigger Job – Series 80 – 3.5# to 5# crisp                                               $105            

(Price does not include any necessary parts)

Tighten and lap slide-to-frame fit                                                              $115

Standard dehorn (sharp edges are minimized                                         $70

but outward appearance of pistol looks stock)

Extreme dehorn (every sharp edge on pistol is softened                       $160

to make the entire pistol as hand friendly as possible.

The best choice for hard use pistols)

Supply, install and fit extended mag release                                            $40

Supply, install and fit new pin kit                                                                $35

Test fire pistol after work, adjust sights to POA/POI                              $55

 

 

Finishes

 

Glass bead – matte finish – standard for stainless pistols

(In house service)                                                                                            $120

Parkerizing - (In house service)                                                                    $150

Hot Blue – matte finish                                                                                  $150

Hot Blue – matte rounds and 400 grit polish on flats                             $200

   

Hot Blue – deluxe – matte rounds with 1200 grit polish on flats          $290

Hard Chrome – matte finish                                                                          $200

Polymer over Parkerizing (In house service)                                              $300

 

 

**Shipping to refinisher is billed at actual cost in addition to finishes charge**